- 1 How to open ports in Livebox
- 2 How to open the ports of the Livebox Fiber router
- 3 How to open ports on Livebox 2.1 router
- 4 How to open ports on Livebox 2 router
- 5 conclusion
Livebox routers are generally used by operators such as Orange and Jazztel to manage and configure their clients’ communications. However, sometimes you need to improve your Internet connection, especially for online games and applications. Therefore, this article describes how to open ports in Livebox, because it is essential to optimize the performance of the device.
How to open ports in Livebox
The expression of opening the ports of a Livebox router, really refers to the process of mapping them so that they work correctly with specific Internet applications. The following describes the procedures required for several of the popular models of these routers.
How to open the ports of the Livebox Fiber router
In the same way as the other router models, in Livebox Fibra you have the options of doing this process both automatically and manually. The procedures for each case are as follows:
How to automatically open ports in Livebox Fiber
How Livebox Fiber routers incorporate the standard Universal Plug and Play (UPnP), the opening of ports will be carried out automatically in all those applications that have UPnP compatibility. Support is currently available in most applications.
On the Livebox Fiber router, the UPnP function is enabled by default. In case you need to check the activation of this function or simply if you want to deactivate it for any other reason, the process that you must carry out consists of the following steps:
- The first step is to enter the configuration menu of the Livebox Fiber router.
- Next, on the main screen you must press the option on the upper tab Advanced configuration.
- At this time, you have to select the option Network settings located in the menu on the left.
- Within the menu that appears in the center of the screen, you have to choose the tab UPnP.
- Finally, it is important to check if the box is checked Enable UPnP IGD. In this way the automatic routing of the ports in Livebox Fiber will be activated.
How to open ports in Livebox Fiber manually
- First of all, you have to press on the section of Advanced configuration, within the main screen.
- Next, the option is located in the menu on the left Network settings, and then is selected.
- After this, the tab is chosen NAT / PAP in the central menu.
- To add a new routing rule for a specific port or range of ports on a machine, look for the option Application / service.
- At this point, the type of service or application to be used in the new rule is selected.
- Then, you enter internal port the port on the local machine to which external traffic will be redirected.
- The next step is to introduce in external port, the port or range of external ports.
- To complete the generation of the new routing rule, choose the protocol between TCP, UDP, or both.
- After this, in device choose the computer connected to the network to which you want to apply the newly created rule.
- Finally, click on the button Add to store the new rule.
Through this procedure the rule has already been created. It should be noted that it can be activated or deactivated, in addition to being eliminated.
How to manually open ports in Livebox Fibra Plus with IPv6
Livebox Fibra Plus routers use IPv6 and in order to open ports on them you have to carry out the following steps:
- The first thing you should do is access the configuration of the Livebox Fibra Plus router. You do this through your gateway and entering your password.
- You can find this password on a sticker located under the router, unless you have changed it.
- To open ports in Livebox Fibra Plus with IPv6 you have to enter the Advanced configuration network.
- Then, you access the function NAT / PAP / CGNAT in which you will find the options to add.
- Scrolling down the screen you will see the options available to configure the rules in a personalized way.
How to create a rule
- Now you will need to know the Private IPv4 address of the computer for which you want to open the ports.
- It is important that you assign a fixed IP address. Otherwise, every time you start it, an IP change will be made.
- From here the process is very simple. You just have to fill in all the fields with the necessary data.
- You must use the field of Application / Service to enter a name to help you identify why you opened the port.
- On internal port and external port you have to enter the number of the port you want to open. Also, here you must have selected the TCP or UDP protocol.
- Finally, you enter the IP address of the device for which you are going to open the port, leaving the option for Accept PCP port proposals.
- Right now, you click Add. You just have to wait for the Livebox change the settings and save them.
- You can see that the new rule has been added but the value of the external port has been modified.
- The new value of the port you have to save it in your notes and then delete the added rule.
How to generate a new rule
- Now you have to recreate a new rule using that value of the external port.
- Use the field again Application / Service in order to write the name that will identify the rule.
- You have to write the port number previously noted in the fields of internal port and external, selecting the protocol.
- At this point, before adding the new rule, you must uncheck the option of Accept PCP port proposal.
In this way you have managed to open the port on a Livebox Plus Fiber that uses IPv6. By following this process, you will have the possibility of opening as many ports as you want.
How to open ports on Livebox 2.1 router
There are two basic ways to open the ports on a Livebox 2.1 router. Next, the processes necessary to achieve this in each of them will be described.
How to open ports in Livebox 2.1 automatically
The standard Universal Plug and Play (UPnP) it is built into your Livebox 2.1. In all applications that also incorporate this technology, the opening of ports will be done automatically. Most of the available file download applications already carry the UPnP standard.
This alternative is enabled by default in most Orange Internet routers. However, to verify that you have it activated or in case you prefer to deactivate it, the procedure that must be followed is the following:
- The first step is to enter the Livebox 2.1 router interface in the direction of the router.
- Next, you must select the option Advanced found in the menu at the top.
- After this, you have to choose the option UPnP and DLNA located in the menu on the left side.
- It should be noted that any application that is installed on the devices connected to your Livebox 2.1, such as tablets, mobile phones, computers or consoles, among others, and that are compatible with the technology UPnP, you will be able to open the necessary ports automatically.
- Finally, the check mark is removed from the Enable UPnP IGC and choose the option.
- Every time the applications ports are opened, the same changes will be presented in the route table. From this screen you will also have the possibility to modify or delete the existing configurations. In addition, it will allow you to create new configurations.
How to manually open ports in Livebox 2.1
There are cases in which you prefer to open ports manually. To do this you have to follow the steps indicated below:
- First, you must check the ports that you need to open for the application that is going to be used.
- Next, you need to access the Livebox 2.1 router interface. On the main screen, click on the tab Advanced
- Once you have logged in, you must select the option Nat which is located in the left menu.
- At this time, you have to choose the section of Port mapping.
- A table will be shown immediately and you must select the button + that you can find in the section Setting.
How to create a new configuration
- In the next window you must click on Common applications. In this way you can choose the type of application for which you want to open the ports.
- Now, on the screen that will be displayed, choose the name tab Please select one. There you can choose the name of the application.
- In case it is not listed, the application data must be entered manually.
- The next step is to select the option Copy and the data corresponding to the chosen application will be presented.
- As to LAN IP You have to write the IP address of the computer for which you need to open the ports.
- Protocol type: Here you choose the one that corresponds from the drop-down menu. If you don’t have this information, you can choose TCP & UDP.
- In the fields LAN port and Public port the port or range of ports that the application needs in both cases are entered.
- Activate: In order for the configuration you have chosen to be activated, you must check this box.
- If the application has previously selected all these fields from a list, they will be completed automatically.
- At this point, the data chosen for the new configuration will be presented in a table.
- Next, within the section Set up, Three new buttons will be displayed that will allow you to edit or delete the configurations already created, as well as the creation of new ones.
- Finally, you must choose the option Enter located in the column Set up in order to save the configuration data.
In this way, by completing these simple steps, you will have already opened the ports that you require in your applications. It is recommended that you apply this method in cases where automatic mapping cannot be used. UPnP on your Livebox 2.1 router.
How to open ports on Livebox 2 router
Two options are available for opening the ports on this router model, one automatic and one manual. Here are the indications to carry out these processes:
How to automatically open ports in Livebox 2
The Livebox 2 router has the standard built-in Universal Plug and Play (UPnP). For this reason, the opening of ports is carried out automatically in all those applications that also have this technology incorporated.
Currently most applications to download files are already UPnP. This feature is enabled by default. However, it may be that you are interested in doing the verification on the automatic mapping of the ports, or that you simply prefer to set them to manual mode. In these cases, you have to follow the procedure that consists of executing the steps indicated below:
- The first thing you have to do is enter the interface of your Livebox 2.
- Once you are inside the main screen you have to click on the tab Livebox– Advanced configuration and then select the option UPnP.
- Any application that you have installed on the devices that are connected to your router, such as computers, smartphones, tablets and consoles, among others, will automatically open the ports you need. It is only essential that they have compatibility with the UPnP standard.
- In order to disable this function, you must uncheck the box Enable UpnP IGD and click on the button Keep.
How to manually open ports on Livebox 2
To configure the manual opening of the ports on the Livebox 2 router, the following steps are required:
- First, you must have access to the router interface.
- Once you have authenticated you have to click on the tab Setting.
- After this, you have to locate and press on Network & Services and then in Advanced configuration.
- Next, you have to click on the option NAT / PAT on the new screen that will be shown to you.
- At this time, you need to press the button to Add new rule.
How to set the new options
Option setting should be done as follows:
- Application / Service: In the drop-down menu you must choose the application to be used. In the case that it is not included in the list, the option is selected Edit new rule and the name is entered manually.
- External port: Here you have to enter the port or port range for the application. This field will be filled in automatically when you select an application from the list, but it is not editable. In manual configuration, the same ports are entered for both the external and the internal.
- Internal port: You need to indicate the port or port range for the application. Similarly, the field will be filled in automatically when choosing an application from the list. In manual configuration, the same ports are entered for the external as for the internal.
- Protocol: You have to choose the protocol corresponding to the application. It is recommended to select the option Both of them. If the application is in the list, this option configures itself.
- Device: Here you must choose from the menu that displays the computer from which the ports are being configured.
- Enable: You need to check this box in order for the selected setting to be enabled.
- The final step is to press on the function Keep to get the configuration to be saved.
You have two main options for open ports or range of ports in different models of the Livebox routers. Those options are to do it automatically or to carry out the operation in manual mode.